This paper model is Samaritan Revolver, Hellboy’s weapon, based on the Hellboy comic and film, the papercraft is created by UHU You can download this. This is the Samaritan gun, the big-barreled shooter that Hellboy uses only after muttering Samaritan Gun Papercraft [Way Nifty via ToyCyte]. We thought HAL was pretty cool, but this papercraft model of Hellboy’s Good Samaritan is ridiculously detailed, down to the hammer, cylinder and.

Author: Dashura Tobei
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Literature
Published (Last): 17 March 2016
Pages: 348
PDF File Size: 5.58 Mb
ePub File Size: 9.67 Mb
ISBN: 157-8-23960-415-3
Downloads: 34521
Price: Free* [*Free Regsitration Required]
Uploader: Dozuru

The archway in which this was glues was skinned over completly with two layers of well glued card to give a secure anchorage. The important thing with the stippling is that it be uneven, but consistent.

Hellboy – Samaritan Revolver Free Paper Model Download

And make it look more like this: It’s really starting to take shape now. All times are GMT A superglue accelerator is also usful, but not hugely important.

Send a private message to Plastic Bonsai. I don’t think I’ve ever seen a cardmodel turned into something so fantasticly detailed and so apparently real! You can download the pieces from the link. These last layers were applied with more of a scrubbing motion and very little paint on the brush. Anyhoo, after the rather happy way the colt is turning out, I’ve decided to go for something even chunkier, in the manner of UHU02’s Hell Boy Samaritan Gun.

I’ve made up a ring of paper to the measurments of part 6, made by tightly winding strip of lightly glued paper around a suitably sized former in my case, a curtain roduntil it reached the required diameter, it then had its ends well soaked with superglue and sanded flat, making a VERY tough ring that should handle fair bit of abuse. Send a private message to ThunderChild. Next picture shows a couple of additions to the basic model, that are aesy to add and easily visible in photo’s of the real one.

I think I’ve made this more complicated than nessesary, by asuming that I could build it better than designed, without actually testing to see how the design worked in the first place. I’ve gone the extra and moved up to spray putty a type of thick, heavy build body spray, available from auto parts suppliers for the main sections, as there’s no detail to obscure yet, and it will hopefully make the job quicker.


Papercraft of Hellboy’s Revolver – Neatorama

Pre mixed waterbased wood putty. This is our second custom vinylmation…. Just letting everybody know that we have approved the next 2 designs that will be part of our ongoing custom urban series vinylmation set. Resources saved on this pxpercraft It would probably be different if I tried again…or maybe not.

The second layer fills in much of the area not coverd by the first.

A warmer tone was mixed by adding a bit of mid brown with our original colour, and applied around areas of wear, like the hammer, rear and underside of the weapon. Which is shame, ‘cos i thought it was cool. Firstly, the major parts, all undecoated black.

One of the simplest improvement to the basic kit is to cut out the slots on the side of the top strap. What was the final superglue count? I’m hugely pleased to say it works, when you depress the lever, the pin pulls and the break swings open.

Next trick it to cut out papercrzft first pieces, trace around them, cut out the new piece 1mm inside the line, and glue it to the first.

I remember papercravt grandmother pqpercraft an Origami book when I was pretty young. This hellbly flat and unintresting and not teribly realistic.

Something the instructions would have you do is leave one side of the frame loose so you can fit a retaining pin inside and then close it up. Not a fault of the model, per-se, just a personal choice. It’s puts me in mind of 12 guage shotgun sort of size. I’ve glued pretty much the whole lot to 1mm card, just using white glue. The barrel with the rifling takes the cake! Appologies to UHU02, you are not to be doubted. I aslo added ribbing on the top of the thumb break.


The barrel tun was laminated up to 5mm thick, and fixed in place. I tend to use the wet and dry type. This was quite an engineering feat, and way beyond my normal scope as I’m usually quite happy with non-working replicas. Firstly, I painted the whole grip a nice orangey brown Then I mixed up a glaze of dark purply papercarft brown, and applied it with my trusty demented spider brush in a papercraftt streaky manner a glaze is a mix of paint and varnish to make a semi-tranparent goo.

Page 1 of 4.

Bullets And Paper Cuts: Hellboy’s Samaritan – Geekologie

UHU02’s Hellboy Samaritan build Okay, in the tradition of all things card modeling, I’m going to start a new project before I finish the last one see nothings colt navy build thread It will need a few more coats, though. I noticed watching the movie the other night that there’s a large screw there, so I’ll be going down that route. So I’ve added extra rings in the middle, and gone with simple tubes at the front, and horseshoe shapes in the top, but this leaves me with a seam accross the middle of the chambers that the “proper” design wouldn’t.

This method gives an amazingly strong component, much stronger than an equivelent plastic part. The rest of the build has gone relatively smoothly so far, don’t forget to bevel the edges of the outer barrel pices so they fit nice and tight together. The thing you want to acheive when painting a model this size, is not to have the whole thing just one colour.

Actually, this model is very well suited to this building approach, with all its flat sides and sharp angles, and simple colouring.

I guess it was attempt to keep myself, my brother and cousin occupied while she took care of us after school.